PS, "reply all" works for me.

>PS >I wish this email group would have an auto-reply like yahoogroups. I >always have to remember to paste in the sgroup <sgroup(a)sgroup.ca> >address, otherwise the mail just replies to the poster.

Thanks for that info Dennis - I'll give it a try. I hardly ever even switch my S550 on these days but it certainly would be nice to fix it. Regards - Colin PS I wish this email group would have an auto-reply like yahoogroups. I always have to remember to paste in the sgroup <sgroup(a)sgroup.ca> address, otherwise the mail just replies to the poster. ________________________________________ On Sep 22, 2011, at 4:33, dennis barton wrote: _______________________________________________ Sent by the sgroup mailing list sgroup(a)sgroup.ca For subscribe/unsubscribe: http://www.sgroup.ca/mailman/listinfo/sgroup See http://www.generalconcepts.com/sgroup/ for more information.

Thanks Dennis on both counts! Just used Reply All and will look at the resistor. Where did you get the schematics from? On Sep 22, 2011, at 17:44, dennis barton wrote: > > I just looked at a schematic, and there's fusible resistor, some buffer resistors and that's about it between the jack and the uPD chip. Probably an easy fix. I'd guess look right at the jack before it connect to the CPU board. > > PS, "reply all" works for me. > > At 9/22/2011 03:38 AM, Colin Shapiro wrote: >> Thanks for that info Dennis - I'll give it a try. I hardly ever even switch my S550 on these days but it certainly would be nice to fix it. >> >> Regards - Colin >> >> PS >> I wish this email group would have an auto-reply like yahoogroups. I always have to remember to paste in the sgroup <sgroup(a)sgroup.ca> address, otherwise the mail just replies to the poster. >> ________________________________________ >> >> On Sep 22, 2011, at 4:33, dennis barton wrote: >> >> > >> > I thought just one fusible resistor fails if you do this. Maybe an easy fix? >> > >> > At 9/21/2011 03:37 PM, you wrote: >> >> Hi Garth, >> >> >> >> Whatever you do, do NOT try to use an old Microsoft mouse. The plug is the same as the S550 but the pin config is different. I tried and blew the board on mine and now I have to use the front panel only. >> >> >> >> Regards >> >> Colin >> >> __________________________________________________________ >> >> >> >> On Sep 21, 2011, at 4:06, Garth Hjelte wrote: >> >> >> >> > Hi, I just got a S550 off eBay, wanted to support S550 a little more. >> >> > >> >> > It has a problem; it looks like the down-arrow button is stuck or something. When I hooked the unit to a monitor, the cursor goes down by itself constantly. >> >> > >> >> > Rather than returning it, I wanted to get a mouse for it (didn't come with one). Where can one get a mouse for these units nowadays? >> >> > >> >> > And can it be used for the S760 as well? >> >> > >> >> > Garth Hjelte >> >> > Sampler User >> >> > >> >> > _______________________________________________ >> >> > Sent by the sgroup mailing list >> >> > sgroup(a)sgroup.ca >> >> > For subscribe/unsubscribe: http://www.sgroup.ca/mailman/listinfo/sgroup >> >> > See http://www.generalconcepts.com/sgroup/ for more information. >> >> >> >> _______________________________________________ >> >> Sent by the sgroup mailing list >> >> sgroup(a)sgroup.ca >> >> For subscribe/unsubscribe: http://www.sgroup.ca/mailman/listinfo/sgroup >> >> See http://www.generalconcepts.com/sgroup/ for more information. >> > >> > >> > Dennis Barton <db(a)skylab2000.com> >> > Brainforest Productions, Los Angeles >> >> _______________________________________________ >> Sent by the sgroup mailing list >> sgroup(a)sgroup.ca >> For subscribe/unsubscribe: http://www.sgroup.ca/mailman/listinfo/sgroup >> See http://www.generalconcepts.com/sgroup/ for more information. > > > Dennis Barton <db(a)skylab2000.com> > Brainforest Productions, Los Angeles